The layout of this Allen Bradley product segment is becoming a trend

2023-01-10

More than 10 oil equipment can be arranged, and the input system can be combined with a high-resolution graphic display via a new patented Profiline keyboard or a built-in USB port. The layout of this Allen Bradley product segment is becoming a trend.

As the world's top PLC product, "DSP" has been in mass production since 2004. With many years of experience, it insists on independent operation and constantly provides customers with excellent products, services and solutions. With the development and progress of the industry, programmable controllers have been widely used. At present, the most widely used devices are: programmable logic controller (PLC) and single chip microcomputer, but whether you use a single chip microcomputer or PLC, its main function is to complete the reaction through the program.

Generally, the purpose of PID control is to control speed and position. The so-called "pneumatic control to industrial control" refers to the control of the movement of equipment, while for industrial control, it refers to whether the precise position and speed can be controlled. Usually, servo control replaces the core of the commonly called servo controller. Because plc has the advantages of motion speed and position control, it also has linear servo and analog control, so there are strict requirements on position, speed, acceleration, motion mode in some occasions. The task of analog control can also be used to control position, pressure and force.

The key of torque control is the effective operation of the motor. In motion control situations, the motor parameters are required to meet the requirements of GB 1633. The motion control product receives and processes the correct input signal of the motor, and externally provides DC4~20mA analog signal and DO/I/O extended analog signal. The analog signal of DO/I can be the analog input signal of PLC, and the DO/I/O expansion slot sends pulses. Pulse module input high speed 24V, digital output low level 0V, maximum expansion 3A. The extended analog signal can only be connected to one relay. This allows the equipment to use high-speed, multi axis channels; At the same time, in order to ensure the configuration, performance and maintenance convenience of high-speed modules, it is necessary to install and configure channels.

AC high-speed, multi axis: digital output up to 5000Hz, can be configured to 4kW to 400kW (3Kw) high resolution;

AC high-frequency series: up to 1092 communication channels, which can be used in Asia, and up to 1 communication channel;

AC high-frequency series: the communication channel can reach 1Mbit, and the resolution can be configured from 4kW to 150kW (1M);

High precision series: the communication channel can reach 1Mbit, and the resolution can be configured to 100A;

For model selection, please refer to the motor driver model 2022/09/07/15, which is compatible with SK-402, and can be expanded as needed;

The last two configurations are optional: EtherCAT bus (only EtherCAT bus and CANopen bus) Profinet communication, Modbus bus (only optional standard configuration (such as ASCNET bus) between EtherCAT bus and CANopen bus), used for communication between I/O modules and PLC modules and bus S2000 communication, between I/O modules and CANopen bus can be used to connect PROFIBUS or PROFIBUS DP (no connection required), and the maximum control current is 1050A, which can achieve a large expansion.

It is used for synchronous communication based on standard Ethernet protocol. The command signal can be used for incremental encoder type, position control or absolute encoder output contact, external power supply or DC ON or DC OFF control output contact.

Multiple instruction processing speed can reach 021 μ s. The debugging time is shortened and the stability is improved.

Single phase AC200V~240V, about 14A NPN input; Single phase AC400V~440V.

※ The cam design is adopted to make the mechanical quantity controlled by a closed loop system, which greatly reduces the mechanical wear. At the same time, it also provides movement and accurate speed according to the requirements of equipment.

During operation, in order to prevent the intervention of the person with mechanical out of step from exceeding the normal working time by 270 minutes, thus affecting its use;

※ It shall be able to operate at low speed under standard load, generally 01 to 03 to 3 times of rated torque.

□ Since the transmission power supply requires stable speed and high accuracy, it can meet the requirements of high-speed operation;

□ Because the linear transmission element will produce great inertia at low speed, it can be used in a short time. Sometimes the servo motor is required to switch slowly.

Without considering this situation, you will find on the robot system that manufacturers or service providers are welcome to help them weld small pieces of equipment.

□ Robots deploy cleanrooms, but many other components can monitor levels. Do not use a proportional quantity to estimate the value.

□ The radiation source will be covered by the probe surface. If the probe surface is covered, the final temperature emitted by the probe will be lower than its measurement temperature.

□ The system will cover a specific probe inside the probe to know whether there is data record inside the probe. In this way, it will have multiple probes to record data while generating and retaining the original sensor performance.

□ If the output of a sensor is very short, and a sensor must be grounded when all data lines change from soil to any sensor from installation to housing

□ Use the grounding spring and multimeter to measure the top of or near the sensor. They have available insulation or plastic pads to ensure grounding. There are two installation methods for the measurement results.

□ When passing the grounding spring grounding ring and grounding terminal, the jumper must be bound. The grounding terminals and connectors shall be installed on both sides between the vertical and horizontal axes as far as possible.

□ Do not add grounding at the grounding spring or welding end or directly perpendicular to the connector body, and the grounding device is in good condition.