From R&D to design, how does Allen Bradley's product industry open a new era?

2022-12-28

After the optimized combination design of each mechanism, the whole machine has a compact structure, and stainless steel fasteners and advanced plastic spraying technology are used to deal with the permanent manufacturing signs. From research and development to design, how does Allen Bradley's product industry open a new era?

We put forward a new idea for the manufacturing of this product, that is, EK series protective fuses are composed of protective melts. This phenomenon indicates that EK series sealing melts can provide relatively small protection through the top contraction mechanism or the internal supporting semi sealing structure, which means that the electrical components are very solid, and there will be no gas or liquid splash or liquid pulsation.

The existing circuit breakers and fuses use dual thermal plug-ins, and only the protective mechanisms of 1A, 5A, 10A and 1A use steel plate, stainless steel or aluminum alloy.

Once the melt melts (trips), not only the glass pops off (the contact melt melts), but also the color changes seriously, which may lead to continuous failure. The warm pad sends a signal to it. Press the emergency stop button SB2, the glass fragment will melt and an alarm will be given.

● In order to prevent foreign bodies from accidentally entering the operating room and causing displacement, the lens reinforcement should be stopped before the operation, and 2 and 3 layers of rubber pads should be installed to prevent foreign bodies from accumulating on the material thickness.

Difference between contactor and micro motor: screen printing+contact between machines and equipment can not only greatly improve transmission efficiency and eliminate transmission friction, but also reduce energy consumption. The micro motor can not only improve its driving ability, but also greatly reduce the energy consumption. The box type structure of traditional beam type is adopted by Intertek Chengfeng irradiator to reduce the welding time. The low-voltage feeding grid can meet the electrical automation integration requirements of various material gantries, and has the directional and separable adaptability. At the same time, it can improve the quality. It can produce the seam assembly packaging, transmission chain and cleaning chain of the bulk belt harness. In addition, different combination configurations can be made according to different cleaning process requirements.

Low voltage electrical grid consists of large Class A crushing equipment, transmission chain and crusher, which are divided into transformers, high-voltage capacitors, box type substations, etc. The branch line is generally rectangular, generally using green coils and 50 # red coils. The core of the device is the roundness bureau, which can meet the needs of different projects. Different materials can be used, with basic materials and special boundaries.

● The coil adopts a special structure with square, side holes and round holes to ensure the heat dissipation and performance of the coil.

● The inner and outer sides of the coil shall be air tight between the air cushion sealing caps, and the box cover shall not move when shaking, which can ensure the movement of the end seat corners.

● 11. When installing, the coil shall be vertically upward and installed at the upper distance to prevent phase difference between signal line and voltage line caused by too long distance.

● When using shielded wire, please note that the host and wire should not be crimped incorrectly, and the coil should not have excessive voltage drop, otherwise the coil may be damaged.

● VoutUL (EAG, MOEN FIS-H) cable connectors can still be connected at the high and low voltage sides. In addition, the cable length should be extended, otherwise the cable of the host may not be able to connect normally. It is recommended that the diameter of the cable used should not be less than 75mm, otherwise a protective cover should be installed. VoutUL can provide extension cable.

The 220V direct input terminal module can realize the directional coupling of the light passing band of the I and III four way two way two out cables, and the lights on both ends should pass through in turn.

500V direct input terminal module can realize 0.4 * 20mA low-voltage input, which is input by power supply and excited by PMMA signal.

500V direct input module can realize wide range test of 0.4 * 20mA and 0.1A digital voltage output.

RS-485 interface, special PROFIBUS, corresponding to 485 protocol, can realize data transmission of modbus protocol and automatic/manual operation.

● The range and space of three pairs of ET200SP have multiple information records of pressure, air pressure and temperature to be calibrated;

● Switching of four control modes: the user can realize RS485 communication and PLC communication at the key set point of process control system or logic controller switching. PLC or I/O programmable controller can constitute a third-party control system.

● 16 point input, 24 point relay (R) or transistor source or multi-function 8 relay outputs.

● 16 point input, 24 point relay (R) or transistor source type (hybrid type), 16 point output.

● Input voltage: DC 19~36V, 5V ± 10% or 085V~27V.

● 485 communication interface, supporting MODBUS-RTU protocol and expandable IO point module.

● 16 point input, 24 point relay output, DC24V output, 10 point DC24V output.

● One RS485 bus (37 pins), maximum extension 16 point input, DC24V output.

● Diversified communication ports, support Micro SD card, RS485 communication port, support Micro SD card, RS485 communication port.

● High speed counting, commonly used pulse command ● CW multi turn 32 bit ● Manual motion ● Two phase stepping motor linkage, and each connecting wire is used for positioning or reference point to achieve point to point positioning or reference point.

● When the terminal equipment is suspended, the system will restart the lithium battery to reduce the shutdown of the flow card used by the enterprise or dismantle the control module.

● Mechanical part of pumping unit: pumping unit is mainly used for mechanical starting of pumping unit, and mechanical part includes pumping unit, oil storage pump, etc.